Manual Self-collection

Blood (EDTA)

About this test kit

With this test kit, you can collect a blood sample yourself. Using the included return envelope, you can send the material to the certified laboratory, where it will be analyzed. If you have any questions, you can always contact our helpdesk through the website.

Contents of the test kit

  • 1 blood collection tube (EDTA)
  • 1 return envelope
  • 3 lancets
  • 1 barcode sticker
  • 1 tube holder
  • 2 plasters
  • 2 alcohol wipes
  • 1 gauze pad
  • 1 instruction manual
  • 1 activation card
  • 1 protective bag with absorbent pad

Not complete? Please contact us.

Before you start

  • Make sure you are seated calmly and relaxed during the sample collection.
  • Do not take the test if you have just exercised.
  • Preferred time for collection: in the morning, usually between 7:00 and 10:00.
  • You must be fasting before taking the test.
  • Do not take the test if you have a fever or acute infections (unless specifically being tested for that).
  • Avoid using medication or supplements shortly before the test.
  • Preferably do not take a sample on Friday or during the weekend due to longer shipping times. Ideally send it on the same day as the collection.
  • Outside below 4°C or above 25°C? Hand in the package at a post office.

Important Information

  • The test kit is for single use only.
  • For collecting a blood sample only.
  • For persons aged 18 and older only.
  • Keep out of reach of children.
  • The supplied materials are intended for personal use only.
  • Do you have difficulty with a finger prick or feel uncomfortable at the sight of blood? Then perform the test in the presence of someone else or consult a healthcare professional.
  • Are you using blood thinners or do you have a blood clotting disorder? Consult your doctor first to avoid complications.

Start here

  • Activate the kit using the details on the activation card.
  • Keep the activation card in a safe place.
  • Place the barcode sticker marked EDTA vertically on the collection tube.

Note

Place the barcode sticker vertically on the collection tube.

1Blood (EDTA)

Step 1.

  1. Drink enough water 30 minutes before the blood draw.
  2. Wash your hands with soap for 30 seconds, rinse them thoroughly with warm water, and dry them well.
  3. Hold your hands against a cup of warm water for 2 minutes.
  4. Swing your arms along your body 8–10 times.

Step 2.

Twist off the cap of the purple collection tube. Place it in the holder for the collection tube. Then remove the cap from the lancet. It is now ready for use.

Step 3.

Choose a puncture site, preferably the side of the tip of your middle or ring finger. Disinfect the site with the alcohol wipe before pricking and allow the finger to dry.

Step 4.

Place the lancet on the disinfected site and press firmly until you hear a click. Ask someone for assistance if needed. Wipe away the first drop of blood with the gauze pad.

Step 5.

Fill the purple collection tube up to the top line. Stand upright and keep your hand pointing downward. Massage the finger from the palm toward the fingertip. Let the blood drip into the tube or collect it with the edge of the tube. Repeat steps 3–4 if this puncture site does not produce enough blood and use the extra lancets.

Step 6.

Place the cap on the collection tube and press firmly until you hear a click. Then gently tilt the collection tube 8–10 times.

2Final check

Kit activated?

Use the codes on your activation card.

Barcode sticker applied?

Place the sticker vertically on the tube.

Below 4 °C or above 25 °C?

Drop off the package at a post office.

3Shipping

Step 1.

Put the sealed collection tube into the protective pouch with the blue adhesive strip, which already contains the absorbent pad. Seal the protective pouch securely with the adhesive strip. Place the pouch with its contents into the box and close the box.

Step 2.

Put the box into the supplied return envelope and seal it with the adhesive strip. The package fits in a mailbox. If you drop it off at a post office, do not add track & trace, as this will delay shipping. Postage has already been paid.

Step 3.

Dispose of the remaining items in the designated waste bin. We’ll notify you by email as soon as your lab results are available.

Symbol Meanings

  • Keep dry
  • For single use only
  • Avoid sunlight
  • Store between temperatures
  • Do not use if the packaging is damaged
  • Read the instructions for use
  • In-vitro diagnostics
  • European Conformity
  • Item number
  • Batch number
  • Expiration date
  • Manufacturer